Skip to content

Batch analysis: overview, dosing, lab, batch list, data quality

Analytics › Batches shows the process and quality of the batch plant. The management view of production (how much was produced, how long the plant was available, how much material one unit of product used) lives on the Campaigns page with the Campaign add-in, and here on the Production tab without it. Lab, Batch list and Data quality show the campaign, the batch and the sample in one chain, against each batch’s own template limits. A gap is always stated, never shown as zero.

  • Permission: analytics:view and batch:view. Recomputing needs batch:close, creating the production sheet batch:configure.
  • The Analytics module and both Batch record add-ins are switched on. It works without the Campaign add-in, on continuous plants too.
  1. Open Analytics › Batches. The Overview tab opens (with or without the Campaign add-in). With the Campaign add-in the management view of production (produced quantity, availability, specific use, time balance, failure root causes, campaign comparison) is campaign-level, so it lives on the Campaigns page; an older “Summary” link takes you there with the filter. Without the Campaign add-in (continuous plant) the Production tab opens. The filter (plant, product, campaign, period) applies to every tab; the lab status and batch status filters show only on Lab, Batch list and Data quality. An older link (to a metric or a batch) opens on the matching tab.
  2. Overview. From the visible batches: batch count (closed, open), median cycle time with its middle half (25–75 %) and range, lab deviation share (closed batches with at least one out-of-limit result ÷ those with at least one judged result; an expected but unsampled point does not count, batches without a judged result are on a separate line), and the dosing deviation: steps have no prescribed tolerance yet, so instead of a “share outside tolerance” the page says so and shows only the distribution (how many batches’ largest deviation is < 1 %, 1–2 %, 2–5 %, ≥ 5 %), without colour or verdict. If the template has a ratio metric with a band, its share outside the band is shown here too. Below, the cycle time per batch with campaign boundaries (dashed vertical line with the campaign number).
  3. Dosing. Per step, the closed batches’ prescription, the actual median and range, the deviation relative to the prescription ((actual − prescribed) / prescribed) and the mean absolute deviation; the number of steps without an actual is stated. The Trend button (or the picker) shows one step’s deviation or actual, or a template ratio metric, per batch; for the deviation the dashed line is the prescription (0 %), for the ratio the template band, points outside the band marked.
  4. Production (only without the Campaign add-in): the KPI row. Produced quantity (from the production sheet’s produced-quantity column, “source: summary”), by-product, availability, productive time share, and per material the specific use (material / produced quantity). The ratio cards show their formula and the two numbers they used. Specific use counts only production sheets that have both the material and the produced quantity; the number left out is on the card. The by-product and availability cards show their own fill rate. If the filter covers several units, the produced quantity is not added up: the page asks you to filter to one product. The basis is the selected period, and the page says so. Below it, the summary KPIs (Sched %, Prod %, Fail %, Trans %, FPY, EFF) on the same scope.
  5. Production: series and months. The produced quantity Daily or Weekly; a gap means no recorded value for that day or week, not zero. In weekly view the axis shows the first and last day of each week. Beside it, product and by-product per month. The figures can be downloaded as CSV; the file starts with the scope (period, site, filters, fill). Numbers have one format: kg as whole numbers, t, hours and % with one decimal.
  6. Lab. Out-of-limit ratio per point: per sample point and parameter, against the batch’s own template limits; the denominator is the number of batches with a judgeable result, batches without a sample are shown beside it (“n without sample”). Trend per batch: choose a metric (cycle time, section, lab pair, step); the horizontal axis is the batch, by start, and a missing value is a gap. For a section or a lab pair the template’s low and high limit is drawn too.
  7. Batch list. Batches per campaign, those outside campaigns on their own row; Campaign analysis, the list’s campaign column and the selected batch’s campaign number open the Campaigns page with the same plant, product and period, the campaign selected. List columns: batch, product, plant, campaign, status, start, end, Cycle time (h), Open for (h), lab (the batch list badge; hover or tap it for the reason), out-of-limit pairs, unsampled points, crew. Click a batch for the cycle time per section, the lab per point, prescribed and actual values and the samples; Batch record opens the sheet. The list can be downloaded as CSV.
  8. Data quality. Gaps: how many batches there are, batches without samples, samples without a batch, batches outside campaigns, batches without timing. If a closed batch has no analysis fact yet, Recompute fills it in. Below, the Daily production sheet: the sheet’s columns with their role (time category, produced quantity, by-product, material, waste, rework, root cause), the number of filled days and the root causes. If the product has no sheet yet, Create production sheet (pick a product and a plant). At the bottom the reconciliation row (with the Campaign add-in): per campaign the production sheet’s material column total and the sum of the paired step actuals of the campaign’s batches, the deviation relative to the sheet total. A deviation outside the tolerance (2 % by default) or a batch without an actual gives a warning; it does not correct either number; a column and a step in different units are not compared (stated). You set the pairing (which material column matches which template step — the picker offers the numerically prescribed steps of the product’s published templates, and saving accepts nothing else) and the tolerance right there (batch:configure); for an imported tenant the loader fills it in from the mapping. If a batch of the campaign has no actual on the paired step, the total is incomplete: it says so instead of a deviation figure (an incomplete total would always look smaller), but shows the facts: the sheet total, the total of the batches with the actual, and how many batches have it (n / m). On a narrow screen the rows are cards with the warning at the top. Re-running the loader does not overwrite your pairing, but a pair you deleted comes back from the mapping — to drop a pair for good, pair the column with another step or ask for the mapping to change.

Your provider can set this page up for your company. When you can choose between more than one view, a view picker appears next to the site picker, with an “i” that opens this article; with a single view nothing is shown. A view can include a time chart (closed batches by day, week or month, per product, with the median lead time) and a specific-use row (per material, the mean and median per batch). The per-tonne value appears only where the batch mass is filled in; “n / N” tells you how many of the N batches the figure is based on. “No data” or a gap in the chart means nothing was recorded for that period, not zero.

The numbers in the gaps panel match what you see on the batch sheets, a missing value in the trend is a gap, and the out-of-limit rows show the unsampled and not-judged counts beside them.

What you see Why What to do
“The Batch record add-in (or Rolling data series) is not enabled for this company.” One add-in is missing. Contact OPEREX.
“No closed batches on this site yet.” The analysis counts closed batches. Close a batch, or set the status filter to All.
“n closed batches have no analysis fact yet” Imported, or closed before this version. Recompute.
KPI: “pick a campaign…” The produced quantity comes from the campaign. Filter to a campaign.
Production: “no data” for availability The production sheet has no time-role column, or none of its rows falls into the selected period. Check the column table on the Data quality tab.
I cannot find the Summary tab With the Campaign add-in the production summary is on the Campaigns page. Analytics › Campaigns (an older link takes you there by itself).

Last updated: